Brand: DFRobot
Model: FIT0100
Introduction: A row of right angle headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers..
1.05€
Ex Tax:0.84€
Brand: DFRobot
Model: FIT0105
Introduction
These are a longer version of our standard break away headers. They are 10mm long which allows you use them socket to socket. The plastic separator can be slid up or down to accommodate your needs. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. ..
1.01€
Ex Tax:0.81€
Brand: DFRobot
Model: FIT0084
Introduction
This is 40 Pin 2.54 mm Single Row Pin Header Strip. It is great for our FIO and custom PCBs or general custom headers. Can be cut to any size...
1.01€
Ex Tax:0.81€
Brand: DFRobot
Model: FIT0084(Blue)
Introduction
This is a blue colored 40 Pin 2.54 mm Single Row Pin Header Strip from DFRobot. These 0.1" header strips are commonly used as low-cost Arduino connectors. The standard spacing allows use with solderless breadboards, perforated prototyping PCBs, and female headers such as those used o..
1.57€
Ex Tax:1.25€
Brand: DFRobot
Model: FIT0084(Green)
Introduction
This is a green colored 40 Pin 2.54 mm Single Row Pin Header Strip from DFRobot. These 0.1" header strips are commonly used as low-cost Arduino connectors. The standard spacing allows use with solderless breadboards, perforated prototyping PCBs, and female headers such as those used ..
1.57€
Ex Tax:1.25€
Brand: DFRobot
Model: FIT0084(Red)
Introduction
This is a red colored 40 Pin 2.54 mm Single Row Pin Header Strip from DFRobot. These 0.1" header strips are commonly used as low-cost Arduino connectors. The standard spacing allows use with solderless breadboards, perforated prototyping PCBs, and female headers such as those used on..
1.57€
Ex Tax:1.25€
Brand: DFRobot
Model: FIT0084(Yellow)
Introduction
This is a orange colored 40 Pin 2.54 mm Single Row Pin Header Strip from DFRobot. These 0.1" header strips are commonly used as low-cost Arduino connectors. The standard spacing allows use with solderless breadboards, perforated prototyping PCBs, and female headers such as those used..
1.57€
Ex Tax:1.25€
Brand: DFRobot
Model: FIT0030
These are 9"(23cm) long jumper wires terminated as female to female. Use these to connect from any male header on any board such as DFRobot IO Shields. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one pack of ten jumpers (colors may vary).
We use these wires fo..
3.85€
Ex Tax:3.06€
Brand: DFRobot
Model: FIT0064
Introduction
Suitable for all kinds of circuit boards, sensors, mechanical support of the installation. They are great for building a multi-level robot chassis. This 10-pack of standoffs includes 10 sets screws and nuts for securing the top of the standoff to your project.
Specifications
&n..
8.05€
Ex Tax:6.41€
Brand: DFRobot
Model: FIT0021
Introduction
This is a 128x64 liquid crystal display that support Chinese character , English characters and even graphics, very suitable for interactive work with Arduino.
Specifications
Voltage: 5V
Blue backlit
Controller: ST7920
Size: 93x70mm
Documents
Setting Pixels ..
22.47€
Ex Tax:17.90€
Brand: DFRobot
Model: DRI0001
This Motor shield for Arduino uses L293 chip which allow to drive two 7-12V DC motors with maximum 1A current. This shield can be directly mount onto standard Arduino Duemilanove and Arduino Mega.
Specification
2 way 7-12V motor drive
Up to 1A current each way
Pin 5,6,7,8 are used to dr..
17.21€
Ex Tax:13.71€
Brand: DFRobot
Model: DRI0002
This is a4.8-46V, 2A Dual Motor Controller which is the revised version of the DF-MDV1.0. Its performance has been improved greatly. It can bear larger current due to the increased haetsink dissipation. It is easy to control, using LGS's outstanding high-power motor driver chip, the L298N. This chip..
17.50€
Ex Tax:13.94€