Brand: Sparkfun
Model: PRT11156
Description: DB9 connectors are a great way to make a tight connection on your project or to plug into existing serial lines. Now you can make your own DB9 cables the easy way with these crimp-on ribbon cable connectors. These work great with our 10-wire ribbon cable, you just need to peel back the ..
2.99€
Ex Tax:2.38€
Brand: Sparkfun
Model: LCD09568
Description: This is the latest evolution of our serial LCD. Included on a single board is a 20x4 LCD and an embedded circuit based around a PIC 16F88. The on-board PIC takes a TTL serial input and prints the characters it receives onto the LCD. The installed firmware also allows for a number of spe..
30.57€
Ex Tax:24.35€
Brand: Sparkfun
Model: LCD00258
Description: The serial enabled LCD backpack allows you to control a parallel based LCD over a single-wire serial interface. The SerLCD backpack takes care of all the HD44780 commands allowing seamless integration with any micro that can communicate over a wide range of TTL serial baud rates. The Se..
18.22€
Ex Tax:14.52€
Brand: Sparkfun
Model: LCD10097
Description: This easy to assemble kit gives you all the parts necessary to assemble a serial 16x2 character LCD display. By sending commands over a serial port from your computer or microcontroller, you can display basic text on the included LCD display.
The main controller IC comes preprogramme..
30.57€
Ex Tax:24.35€
Brand: DFRobot
Model: FIT0033
Introduction
This is a 300mm servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on the servo allows. Male connector on one end goes to controller, female connector mates with servo. Fits all Hitec, Futaba, JR, Multiplex, and Airtronic..
3.04€
Ex Tax:2.42€
Brand: Pololu
Model: POLO/779
This is a great 6-inch (150-mm) board-to-board cable for devices that have 0.1" 3-pin male header connectors, such as RC servo controllers, RC receivers and motor controllers. It can also be a convenient way to connect various sensors to a robot controller...
4.00€
Ex Tax:3.19€
Brand: Pololu
Model: POLO/2170
This 3-wire harness can be used to add a toggle switch between any two devices that can be connected with “JR” style servo connectors. One side of the switch has a lead with a female connector, while the other side has two leads, one male and one female.
We sell two versions of this harness:
..
5.01€
Ex Tax:3.99€
Brand: Pololu
Model: POLO/2171
This 18" (45 cm) harness has an inline on/off switch, with a 0.1" 3-pin female connector on one end and both a male and a female connector on the other.
This 3-wire harness can be used to add a toggle switch between any two devices that can be connected with “JR” style servo connectors. One side ..
6.02€
Ex Tax:4.80€
Brand: Pololu
Model: POLO/788
This 12-inch (300-mm) Y-cable has “JR” style connectors on all ends and is typically used to connect two servos to one servo port. As such, it has a single female and two male connectors (though in the RC hobby industry female connectors are often referred to as “male” and vice versa)...
7.03€
Ex Tax:5.60€
Brand: DFRobot
Model: FIT0005
Introduction
This mounting bracket is designed for Sharp GP2D12/2D15.
The color of bracket may vary and not the same as shown in the picture.
Specification
Size:45x20x15mm
Mounting hole distance:14mm
Weight:5g..
8.10€
Ex Tax:6.45€
Brand: Sharp Microelectronics
Model: POLO/136
Overview
The Sharp distance sensors are a popular choice for many projects that require accurate distance measurements. This IR sensor is more economical than sonar rangefinders, yet it provides much better performance than other IR alternatives. Interfacing to most microcontrollers is straightfo..
19.23€
Ex Tax:15.32€
Brand: Olimex
Model: SHIELD-LCD16x2
Description: Arduino compatible Serial / I2C LCD shield with LCD16x2 with backlight and 4 buttons, Arduino library and demo examples. Accepts commands by UART or I2C.
Documents: Here..
20.14€
Ex Tax:16.05€