Brand: Pololu
Model: Wheel/1439
These white plastic wheels press fit onto the 3mm D shafts of our mini and micro metal gearmotors to make a nice drive solution for small robots. The wheels have silicone tires and measure 90 mm (3.54") in diameter. Two additional mounting holes make it possible to use the wheel with several of our ..
13.16€
Ex Tax:10.48€
Brand: Olimex
Model: OL-BA-1400
This is a rechargeable Li-Po high discharge current battery with JST connector ready to plug to:
OLIMEXINO-328, OLIMEXINO-STM32, PIC32-PINGUINO, PIC32-PINGUINO-OTG, DUINOMITE and DUINOMITE-MEGA
The battery has overcharge and short circuit protection.
Features:
Charge voltage 4.2V, nom..
13.26€
Ex Tax:10.56€
Brand: Olimex
Model: OL-BA-250
Description: This is a rechargeable Li-Po high discharge current battery with JST connector. The battery has overcharge and short circuit protection.
Features:
Charge voltage 4.2V, nominal voltage 3.7V, cut-off voltage 3.0V
Recommended charge current 50mA
Max charge current 125mA
Re..
9.01€
Ex Tax:7.18€
Brand: Robomaa.com
Model: RM-BA-250
Description: This is a rechargeable Li-Po high discharge current battery with JST connector. The battery has overcharge and short circuit protection.
Features:
Charge Limited Voltage 4.2V
Nominal Voltage 3.7V
Nominal Capacity 250mAh@ 0.2C Discharge
Nominal Capacity refer to the ..
9.01€
Ex Tax:7.18€
Brand: Olimex
Model: OL-BA-800
↵
Description: This is a rechargeable Li-Po high discharge current battery with JST connector. The battery has overcharge and short circuit protection.
Features:
Charge voltage 4.2V, nominal voltage 3.7V, cut-off voltage 3.0V
Recommended charge current 160mA
Max charge cu..
10.02€
Ex Tax:7.98€
Brand: Sparkfun
Model: TOL10950
Description: Polymorph is a non-toxic, biodegradable polyester with a low melting temperature of about 60°C (140°F). Prototype plastic parts can be made by simply heating the plastic beads in hot water until they turn clear and then kneading them together and shaping by hand. When it cools it become..
10,119.96€
Ex Tax:8,063.71€
Brand: Sparkfun
Model: DEV10618
Description: This shield allows you to use a computer power supply (or other power source) to use your Arduino to switch high current. With RFP30N06LE MOSFETS, you can easily control a lot of current directly from your Arduino.
The board provides 6 PWM outputs via screw terminals. Check the data..
24.49€
Ex Tax:19.52€
Brand: DFRobot
Model: DFR0105
Introduction: Most project of Arduino may need more than two voltage supply. When feed with from 4.5-35V, this power shield able to provide a voltage range from 1.25-12V with 3A peak current. Ideal for servo control and other non-standard components. With this shield, your Arduino now have one power..
22.47€
Ex Tax:17.90€
Brand: Robomaa.com
Model: RM-POW12/2
Description: Power Supply, 12V 2A, Euro - color and shape may vary
Output Voltage Nom: 12V
Output Current Max: 2A
Output Connector: 5,5/2,1
Plug Type: EU
Center positive..
14.07€
Ex Tax:11.21€
Brand: Pololu
Model: Wire/1801
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1..
11.44€
Ex Tax:9.11€
Brand: Sparkfun
Model: DEV12587
Description: Here at SparkFun, we refuse to leave 'good enough' alone. That's why we're adding to our line-up of Arduino-compatible microcontrollers once more! The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connec..
24.19€
Ex Tax:19.27€
Brand: Sparkfun
Model: DEV12640
Description: Here at SparkFun, we refuse to leave 'good enough' alone. That's why we're adding to our line-up of Arduino-compatible microcontrollers once more! The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connec..
24.19€
Ex Tax:19.27€