Brand: Robomaa.com
Model: RM-115
Description: Nylon short standoffs - M3 x 10 Hexagonal Standoff - 10 Set. Used to get your proto board up off the table...
4.00€
Ex Tax:3.19€
Brand: Robomaa.com
Model: RM-114
Description: Suitable for all kinds of circuit boards, sensors, mechanical support of the installation.
Specifications:
Hexagonal standoffs length: 10 mm
Material: Nylon
Shipping List:
M3 x 10 hexagonal standoffs (10 units)
M3 x 5 screws (10 units)
M3 nuts (10 units)..
6.02€
Ex Tax:4.80€
Brand: Pololu
Model: POLO/1931
These male pins can be crimped on 22-28AWG wires and snapped into our crimp connector housings to create custom cables that are compatible with standard 0.1"-pitch headers and solderless breadboards. Our wires with pre-crimped terminals use these same pins. One male crimp pin pack consists of 100 pi..
14.68€
Ex Tax:11.69€
Brand: Devantech
Model: MD04
Description: The MD04 is a medium power motor driver and is an upgraded replacement for the MD03, the main features are ease of use and flexibility. The motor's power is controlled by on-board Pulse Width Modulation (PWM) generators driving the H-Bridge Transistors. Voltage - 8v - 24v Current - up t..
65.69€
Ex Tax:52.34€
Brand: DFRobot
Model: DFR0035
Introduction
The MEGA IO Expansion Shield can be used for a variety of interactive works, it is often used in a number of sensors or circuit. For those who are familiar with the electronic circuits or universal board with bread board module, it helps in building a simple circuit effortlessly, but..
16.19€
Ex Tax:12.90€
Brand: Sparkfun
Model: DEV11007
Description: It's powerful, it's portable, it's Pro! We're continuing our Pro series of Arduino-compatible micro-controllers with the addition of the Mega Pro. This is a 5V microcontroller running a version of the stk500v2 bootloader at 16MHz. Just like the other Pro-series boards this board is buil..
54.15€
Ex Tax:43.15€
Brand: DFRobot
Model: DFR0016
Introduction
This is a design for an open-source prototyping shield for Arduino Mega. It has tons of cool features, to make prototyping on your Arduino easy. Assembly and soldering is required!
Features:
Reset button up top
Lots of GND and +5V rails
DIP prototyping area makes it easy..
12.04€
Ex Tax:9.60€
Brand: Sparkfun
Model: COM11967
Dot illuminated push-button
LED voltage: 5-12V
16mm diameter
3A/250VAC
1NO 1NC / 2NO 2NC
Front shape: High round
Crust material: Stainless steel / Brass: Nickel Plated
Dot illuminated
IP Degree: IP40/IP67..
10.02€
Ex Tax:7.98€
-20 %
Brand: Pololu
Model: POLO/1633+1479
This semiconductor gas sensor detects the presence of methane (CNG) gas at concentrations from 200 ppm to 10,000 ppm, a range suitable for detecting gas leaks. The sensor’s simple analog voltage interface requires only one analog input pin from your microcontroller.
Shipping list: 1 x Methane Gas..
6.48€ 8.10€
Ex Tax:5.16€
Brand: Seeedstudio
Model: MOT102A2B
Description
Gear (reduction ) motor, made in Shenzheng, China. Pretty good quality, running a speed at 60 rpm. All you need to do is connect the postive and negative pole-pin, simple enough for beginners.
Specifications:
Voltage: 2.4V
No Load: 55 rpm - 30 mA
Maximum Efficiency: 40 rpm ..
19.33€
Ex Tax:15.40€
Brand: Pololu
Model: POLO/1350
The six-channel Micro Maestro takes serial servo controllers to the next level by incorporating native USB and internal scripting control. Whether you want the best servo controller available (0.25μs resolution with built-in speed and acceleration control) or a general I/O controller (e.g. to interf..
38.90€
Ex Tax:31.00€
Brand: DFRobot
Model: FIT0094
Introduction
This motor has a long (0.365" or 9.27 mm), D-shaped metal output shaft that matches the Pololu wheel 42x19mm and 32x7mm. The brass faceplate has two mounting holes threaded for M1.6 screws (1.6 mm diameter, 0.35 mm thread pitch), or you can use the mounting bracket or extended mounti..
19.33€
Ex Tax:15.40€